---
title: "Beverage Filling Valve Assembly"
industry: "Beverage Manufacturing"
verification_protocol:
  urn: "URN:CNFX:ME:BEVERAGE_FILLING_VALVE_ASSEMBLY"
  data_integrity_hash: "ccd4ebb3372baee3b38c69d1927b93bd"
  source_authority: "https://cnfx.com"
  strict_mode: true
source_identity:
  provider: "CNFX Industrial Knowledge Graph"
  index_version: "2026.Q1-Universal"
  authority_id: "URN:CNFX:ME:BEVERAGE_FILLING_VALVE_ASSEMBLY"
  data_source_uri: "https://cnfx.com/llms/industry/beverage-manufacturing/product/beverage-filling-valve-assembly.md"
  official_resource_url: "https://cnfx.com/industry/beverage-manufacturing/product/beverage-filling-valve-assembly"
  is_verified_logic: true
attributes:
  flow_rate:
    status: "config-dependent"
    typical_range: "0.5-6.0 bar (50-600 kPa) at 4-25°C liquid temperature"
    unit: "L/min"
  fill_accuracy:
    status: "config-dependent"
    typical_range: "0.5-6.0 bar (50-600 kPa) at 4-25°C liquid temperature"
    unit: "mL"
engineering_limits:
  max_safe_operating_point:
    value: 8.0
    unit: "bar"
    consequence: "Elastomer seal extrusion through 0.05mm clearance at 8.0 bar ΔP (Poisson's ratio 0.48, Young's modulus 3.5 MPa)"
fmea_matrix_quantitative:
  - node_1:
      trigger: "Particulate contamination &gt;25μm in beverage stream"
      severity: 8
      occurrence: 3
      detection: 4
      mitigation_protocol: "Install 10μm absolute filtration with differential pressure monitoring"
  - node_2:
      trigger: "CIP caustic solution concentration &gt;4.0% NaOH at 85°C"
      severity: 8
      occurrence: 3
      detection: 4
      mitigation_protocol: "Implement conductivity-based CIP concentration control with 2.5% NaOH limit"
bom_nodes:
  valve-body:
    type: "component"
    urn: "URN:CNFX:ME:VALVE_BODY"
    interface_type: "physical-logic-coupled"
  valve-stem:
    type: "component"
    urn: "URN:CNFX:ME:VALVE_STEM"
    interface_type: "physical-logic-coupled"
  sealing-gasket:
    type: "component"
    urn: "URN:CNFX:ME:SEALING_GASKET"
    interface_type: "physical-logic-coupled"
  actuator-interface:
    type: "part"
    urn: "URN:CNFX:ME:ACTUATOR_INTERFACE"
    interface_type: "physical-logic-coupled"
manufacturing_compliance:
  - standard: "ISO 22000:2018 - FOOD SAFETY MANAGEMENT SYSTEMS"
    scope: "Verified Engineering Specification"
  - standard: "ANSI/ASME BPE-2022 - BIOPROCESSING EQUIPMENT"
    scope: "Verified Engineering Specification"
  - standard: "DIN 11850-1:2019 - STAINLESS STEEL TUBES FOR THE FOOD INDUSTRY"
    scope: "Verified Engineering Specification"
url: "https://cnfx.com/llms/industry/beverage-manufacturing/product/beverage-filling-valve-assembly.md"
on_chain_sovereignty:
  contract_standard: "ERC-721-Industrial"
  metadata_hash: "ca65045cec307d092900ce370901de632413bdaf678ff2c5fcf77d0be847fd81"
  royalty_logic: "IPFS-CID-REQUIRED"
  mint_status: "logic-verified-ready"
version: "3.3.4-EXTREME-SOVEREIGN-WEB3"
---

# Industrial Specification: Beverage Filling Valve Assembly

## 1. Technical Definition
Precision valve assembly for controlled liquid dispensing in beverage filling machines

## 2. Engineering Reasoning & Causal Matrix
> **Operational Intelligence**: Designed for **0.5-6.0 bar (50-600 kPa) at 4-25°C liquid temperature**. Failure boundary: **Seal failure at 8.0 bar differential pressure, actuator failure at 12.0 bar backpressure**, Mechanism: **Elastomer seal extrusion through 0.05mm clearance at 8.0 bar ΔP (Poisson's ratio 0.48, Young's modulus 3.5 MPa)**.

### 2.1 Analytical Physics Model
Governed by the **Darcy-Weisbach Pressure Drop**:

> **Primary Equation**: $\Delta P = f \cdot \frac{L}{D} \cdot \frac{\rho v^2}{2}$  
> **Engineering Impact**: Critical for sizing CIP (Clean-In-Place) pump heads.

| Symbol | Variable Definition | Localized Reference |
| :--- | :--- | :--- |
| f | Friction Factor | Engineering Constant |
| L | Pipe Length | Engineering Constant |
| v | Velocity | Engineering Constant |

### 2.2 FMEA (Failure Mode & Effects Analysis)
| Event Trigger | Severity | Failure Mode | Mitigation Strategy |
| :--- | :--- | :--- | :--- |
| Particulate contamination &gt;25μm in beverage stream | 8 | Seat erosion causing 0.15 L/min leakage at 3.0 bar | Install 10μm absolute filtration with differential pressure monitoring |
| CIP caustic solution concentration &gt;4.0% NaOH at 85°C | 8 | PTFE seal degradation causing 180° rotation binding | Implement conductivity-based CIP concentration control with 2.5% NaOH limit |

## 3. Key Technical Parameters
| Parameter | Value | Unit | Status |
| :--- | :--- | :--- | :--- |
| flow_rate | Config-dependent | L/min | Verified |
| fill_accuracy | Config-dependent | mL | Verified |

## 4. System BOM & Knowledge Routing
### Core Components (Recursive Links)
- [Actuator Interface](https://cnfx.com/llms/industry/beverage-manufacturing/product/actuator-interface.md) `(Standalone System)`

### Industrial DNA Context (De-duplicated)
**Complementary Dependencies**: **Beverage Filling Machine**, **Conveyor System**, **Capping Machine**  
**Downstream Applications**: Bottled Water, Carbonated Soft Drinks, Juice Beverages  

## 5. Engineering Risks & FAQ
- **Caution**: 
- **Caution**: 
- **Caution**: 

### Q: What materials are used in this beverage filling valve assembly?
**A**: This assembly uses Stainless Steel 316L for corrosion resistance, Food-Grade PTFE for sealing surfaces, and Medical-Grade Silicone for gaskets, ensuring food safety and durability.

### Q: What is the typical actuation response time for this valve assembly?
**A**: The actuation response time is measured in milliseconds (ms), providing rapid and precise control for high-speed beverage filling operations to maintain production efficiency.

### Q: What temperature range can this valve assembly withstand?
**A**: This valve assembly operates effectively within a specified temperature range in degrees Celsius (°C), suitable for both cold and hot beverage filling applications while maintaining material integrity.

## 6. Manufacturing Compliance
- ISO 22000:2018 - FOOD SAFETY MANAGEMENT SYSTEMS
- ANSI/ASME BPE-2022 - BIOPROCESSING EQUIPMENT
- DIN 11850-1:2019 - STAINLESS STEEL TUBES FOR THE FOOD INDUSTRY

---
### 🛠️ Engineering Resource Access
🔗 **[Full Specification: Beverage Filling Valve Assembly](https://cnfx.com/industry/beverage-manufacturing/product/beverage-filling-valve-assembly)**

### 🌐 Knowledge Graph Topology
> **Node Status**: Verified Engineering Spec
> **Connectivity**: Linked to **4** standalone system nodes
> **Global Context**: Part of a 5,814 node industrial cluster within the CNFX Graph

> **Reference ID**: BEVERAGE_FILLING_VALVE_ASSEMBLY | **Authority**: CNFX-2026-ST-001 | **Fingerprint**: bf6d5d31
