---
title: "CIP Supply Pump"
industry: "Food Manufacturing"
verification_protocol:
  urn: "URN:CNFX:ME:CIP_SUPPLY_PUMP"
  data_integrity_hash: "f320b042c6a67f28d036419faac6e013"
  source_authority: "https://cnfx.com"
  strict_mode: true
source_identity:
  provider: "CNFX Industrial Knowledge Graph"
  index_version: "2026.Q1-Universal"
  authority_id: "URN:CNFX:ME:CIP_SUPPLY_PUMP"
  data_source_uri: "https://cnfx.com/llms/industry/food-manufacturing/product/cip-supply-pump.md"
  official_resource_url: "https://cnfx.com/industry/food-manufacturing/product/cip-supply-pump"
  is_verified_logic: true
attributes:
  spec:
    status: "config-dependent"
    typical_range: "2.5-6.0 bar (36-87 psi) at 15-60°C fluid temperature"
    unit: "m³/h"
engineering_limits:
  max_safe_operating_point:
    value: 3.2
    unit: "m"
    consequence: "Vapor pressure collapse causing cavitation erosion at 0.5-1.0 MPa localized pressure differentials; mechanical seal face thermal stress from 150°C+ localized heating during dry running"
fmea_matrix_quantitative:
  - node_1:
      trigger: "Inadequate NPSH margin (NPSHa &lt; NPSHr + 0.5 m)"
      severity: 8
      occurrence: 3
      detection: 4
      mitigation_protocol: "Installation of booster pump maintaining NPSHa &gt; 4.0 m with 0.1 m resolution pressure transducer feedback"
  - node_2:
      trigger: "Caustic solution concentration exceeding 4% NaOH at 80°C+"
      severity: 8
      occurrence: 3
      detection: 4
      mitigation_protocol: "PTFE-coated seal faces with Kalrez perfluoroelastomer secondary seals rated for pH 14 at 120°C"
bom_nodes:
  impeller:
    type: "part"
    urn: "URN:CNFX:ME:IMPELLER"
    interface_type: "physical-logic-coupled"
  mechanical-seal:
    type: "part"
    urn: "URN:CNFX:ME:MECHANICAL_SEAL"
    interface_type: "physical-logic-coupled"
  casing:
    type: "component"
    urn: "URN:CNFX:ME:CASING"
    interface_type: "physical-logic-coupled"
manufacturing_compliance:
  - standard: "ISO 2858:2012 (END-SUCTION CENTRIFUGAL PUMPS - DESIGNATION, NOMINAL DUTY POINT AND DIMENSIONS)"
    scope: "Verified Engineering Specification"
  - standard: "ANSI/ASME B73.1-2012 (SPECIFICATION FOR HORIZONTAL END SUCTION CENTRIFUGAL PUMPS FOR CHEMICAL PROCESS)"
    scope: "Verified Engineering Specification"
  - standard: "DIN EN 22858:1993 (END-SUCTION CENTRIFUGAL PUMPS - RATING 16 BAR - DESIGNATION, NOMINAL DUTY POINT AND DIMENSIONS)"
    scope: "Verified Engineering Specification"
url: "https://cnfx.com/llms/industry/food-manufacturing/product/cip-supply-pump.md"
on_chain_sovereignty:
  contract_standard: "ERC-721-Industrial"
  metadata_hash: "856622863d323d8eb6a635d1a6943f385f1190b3df830a4e6510f8b99865945b"
  royalty_logic: "IPFS-CID-REQUIRED"
  mint_status: "logic-verified-ready"
version: "3.3.4-EXTREME-SOVEREIGN-WEB3"
---

# Industrial Specification: CIP Supply Pump

## 1. Technical Definition
A pump specifically designed to supply cleaning solutions during Clean-in-Place (CIP) processes.

## 2. Engineering Reasoning & Causal Matrix
> **Operational Intelligence**: Designed for **2.5-6.0 bar (36-87 psi) at 15-60°C fluid temperature**. Failure boundary: **Cavitation occurs at NPSHa &lt; 3.2 m H₂O (NPSHr + 0.5 m safety margin), mechanical seal fails at shaft deflection &gt; 0.05 mm**, Mechanism: **Vapor pressure collapse causing cavitation erosion at 0.5-1.0 MPa localized pressure differentials; mechanical seal face thermal stress from 150°C+ localized heating during dry running**.

### 2.1 Analytical Physics Model
Governed by the **Darcy-Weisbach Pressure Drop**:

> **Primary Equation**: $\Delta P = f \cdot \frac{L}{D} \cdot \frac{\rho v^2}{2}$  
> **Engineering Impact**: Critical for sizing CIP (Clean-In-Place) pump heads.

| Symbol | Variable Definition | Localized Reference |
| :--- | :--- | :--- |
| f | Friction Factor | Engineering Constant |
| L | Pipe Length | Engineering Constant |
| v | Velocity | Engineering Constant |

### 2.2 FMEA (Failure Mode & Effects Analysis)
| Event Trigger | Severity | Failure Mode | Mitigation Strategy |
| :--- | :--- | :--- | :--- |
| Inadequate NPSH margin (NPSHa &lt; NPSHr + 0.5 m) | 8 | Cavitation-induced impeller erosion reducing efficiency by 15-25% within 200 operating hours | Installation of booster pump maintaining NPSHa &gt; 4.0 m with 0.1 m resolution pressure transducer feedback |
| Caustic solution concentration exceeding 4% NaOH at 80°C+ | 8 | Mechanical seal elastomer degradation causing 0.5 L/min leakage after 50 CIP cycles | PTFE-coated seal faces with Kalrez perfluoroelastomer secondary seals rated for pH 14 at 120°C |

## 3. Key Technical Parameters
| Parameter | Value | Unit | Status |
| :--- | :--- | :--- | :--- |
| spec | Config-dependent | m³/h | Verified |

## 4. System BOM & Knowledge Routing
### Core Components (Recursive Links)
- [Impeller](https://cnfx.com/llms/industry/machinery-and-equipment-manufacturing/product/impeller.md) `(Standalone System)`
- [Mechanical Seal](https://cnfx.com/llms/industry/machinery-and-equipment-manufacturing/product/mechanical-seal.md) `(Standalone System)`

### Industrial DNA Context (De-duplicated)
**Complementary Dependencies**: **CIP Solution Tank**, **Heat Exchanger**, **Automated Control System**  
**Downstream Applications**: Sanitized Processing Equipment, Cleaned Piping Systems, Hygienic Food Contact Surfaces  

## 5. Engineering Risks & FAQ
- **Caution**: 
- **Caution**: 
- **Caution**: 

### Q: What makes this CIP supply pump suitable for food manufacturing?
**A**: This pump is constructed with AISI 316L stainless steel, which offers superior corrosion resistance and meets food-grade hygiene standards required in food processing environments.

### Q: How does this pump integrate with existing Clean-in-Place systems?
**A**: The CIP supply pump is designed for seamless integration with standard CIP systems, featuring compatible connections and flow characteristics that work with typical cleaning solution delivery requirements.

### Q: What maintenance is required for the mechanical seal in this pump?
**A**: The mechanical seal requires periodic inspection for wear and proper lubrication according to manufacturer specifications, typically during routine CIP system maintenance cycles.

## 6. Manufacturing Compliance
- ISO 2858:2012 (END-SUCTION CENTRIFUGAL PUMPS - DESIGNATION, NOMINAL DUTY POINT AND DIMENSIONS)
- ANSI/ASME B73.1-2012 (SPECIFICATION FOR HORIZONTAL END SUCTION CENTRIFUGAL PUMPS FOR CHEMICAL PROCESS)
- DIN EN 22858:1993 (END-SUCTION CENTRIFUGAL PUMPS - RATING 16 BAR - DESIGNATION, NOMINAL DUTY POINT AND DIMENSIONS)

---
### 🛠️ Engineering Resource Access
🔗 **[Full Specification: CIP Supply Pump](https://cnfx.com/industry/food-manufacturing/product/cip-supply-pump)**

### 🌐 Knowledge Graph Topology
> **Node Status**: Verified Engineering Spec
> **Connectivity**: Linked to **3** standalone system nodes
> **Global Context**: Part of a 5,814 node industrial cluster within the CNFX Graph

> **Reference ID**: CIP_SUPPLY_PUMP | **Authority**: CNFX-2026-ST-001 | **Fingerprint**: 01a598df
