---
title: "Pick-up Head"
industry: "Machinery and Equipment Manufacturing"
verification_protocol:
  urn: "URN:CNFX:ME:PICK_UP_HEAD"
  data_integrity_hash: "9d7bcf46985906abd690b7fa1f5e52b5"
  source_authority: "https://cnfx.com"
  strict_mode: true
source_identity:
  provider: "CNFX Industrial Knowledge Graph"
  index_version: "2026.Q1-Universal"
  authority_id: "URN:CNFX:ME:PICK_UP_HEAD"
  data_source_uri: "https://cnfx.com/llms/industry/machinery-and-equipment-manufacturing/product/pick-up-head.md"
  official_resource_url: "https://cnfx.com/industry/machinery-and-equipment-manufacturing/product/pick-up-head"
  is_verified_logic: true
attributes:
  spec:
    status: "config-dependent"
    typical_range: "0.5-2.5 N suction force, 0.1-0.5 mm vertical travel, 20-60°C ambient temperature"
    unit: "mm"
engineering_limits:
  max_safe_operating_point:
    value: 0.3
    unit: "N"
    consequence: "Vacuum seal failure due to elastomer compression set exceeding 15% permanent deformation at &gt;70°C; Bernoulli principle disruption from surface contamination &gt;5 μm particle size causing airflow turbulence"
fmea_matrix_quantitative:
  - node_1:
      trigger: "Vacuum pump pressure fluctuation exceeding ±10% of 80 kPa nominal"
      severity: 8
      occurrence: 3
      detection: 4
      mitigation_protocol: "Dual redundant vacuum sensors with 0.5 kPa resolution and PID-controlled pressure regulation"
  - node_2:
      trigger: "Mechanical wear of polyurethane suction cup lip exceeding 0.2 mm thickness reduction"
      severity: 8
      occurrence: 3
      detection: 4
      mitigation_protocol: "Ceramic-coated wear surface with 60 HRC hardness and 0.05 mm wear monitoring sensors"
bom_nodes:
  suction-cup-gripper:
    type: "part"
    urn: "URN:CNFX:ME:SUCTION_CUP_GRIPPER"
    interface_type: "physical-logic-coupled"
  lifting-actuator:
    type: "part"
    urn: "URN:CNFX:ME:LIFTING_ACTUATOR"
    interface_type: "physical-logic-coupled"
  mounting-bracket-arm:
    type: "component"
    urn: "URN:CNFX:ME:MOUNTING_BRACKET_ARM"
    interface_type: "physical-logic-coupled"
  vacuum-line-valve-if-applicable:
    type: "part"
    urn: "URN:CNFX:ME:VACUUM_LINE_VALVE_IF_APPLICABLE"
    interface_type: "physical-logic-coupled"
manufacturing_compliance:
  - standard: "ISO 1940-1:2003 (BALANCE QUALITY REQUIREMENTS FOR ROTORS)"
    scope: "Verified Engineering Specification"
  - standard: "ANSI/ASME B46.1-2019 (SURFACE TEXTURE)"
    scope: "Verified Engineering Specification"
  - standard: "DIN 7184-1:2018 (TOLERANCES FOR LINEAR DIMENSIONS)"
    scope: "Verified Engineering Specification"
url: "https://cnfx.com/llms/industry/machinery-and-equipment-manufacturing/product/pick-up-head.md"
on_chain_sovereignty:
  contract_standard: "ERC-721-Industrial"
  metadata_hash: "30c5c3e96d7ad5ed2d9dc1aca65312d8ffa497d99672ac37d7b1057aa6e97dc2"
  royalty_logic: "IPFS-CID-REQUIRED"
  mint_status: "logic-verified-ready"
version: "3.3.4-EXTREME-SOVEREIGN-WEB3"
---

# Industrial Specification: Pick-up Head

## 1. Technical Definition
A mechanical component in a lamination feeder that precisely lifts and transfers individual sheets or materials from a stack.

## 2. Engineering Reasoning & Causal Matrix
> **Operational Intelligence**: Designed for **0.5-2.5 N suction force, 0.1-0.5 mm vertical travel, 20-60°C ambient temperature**. Failure boundary: **Suction force &lt;0.3 N causes sheet slippage, &gt;3.0 N causes sheet deformation; vertical misalignment &gt;0.15 mm causes transfer failure; temperature &gt;70°C degrades vacuum seal elastomers**, Mechanism: **Vacuum seal failure due to elastomer compression set exceeding 15% permanent deformation at &gt;70°C; Bernoulli principle disruption from surface contamination &gt;5 μm particle size causing airflow turbulence**.

### 2.2 FMEA (Failure Mode & Effects Analysis)
| Event Trigger | Severity | Failure Mode | Mitigation Strategy |
| :--- | :--- | :--- | :--- |
| Vacuum pump pressure fluctuation exceeding ±10% of 80 kPa nominal | 8 | Incomplete sheet pickup due to insufficient suction force | Dual redundant vacuum sensors with 0.5 kPa resolution and PID-controlled pressure regulation |
| Mechanical wear of polyurethane suction cup lip exceeding 0.2 mm thickness reduction | 8 | Vacuum seal leakage &gt;5 L/min at 80 kPa | Ceramic-coated wear surface with 60 HRC hardness and 0.05 mm wear monitoring sensors |

## 3. Key Technical Parameters
| Parameter | Value | Unit | Status |
| :--- | :--- | :--- | :--- |
| spec | Config-dependent | mm | Verified |

## 4. System BOM & Knowledge Routing
### Core Components (Recursive Links)
- [Suction Cup / Gripper](https://cnfx.com/llms/industry/machinery-and-equipment-manufacturing/product/suction-cup-gripper.md) `(Standalone System)`
- [Lifting Actuator](https://cnfx.com/llms/industry/machinery-and-equipment-manufacturing/product/lifting-actuator.md) `(Standalone System)`
- [Vacuum Line / Valve (if applicable)](https://cnfx.com/llms/industry/machinery-and-equipment-manufacturing/product/vacuum-line-valve-if-applicable.md) `(Standalone System)`

### Industrial DNA Context (De-duplicated)
**Complementary Dependencies**: **Lamination Feeder**, **Sheet Stacker**, **Material Handling Conveyor**  
**Downstream Applications**: Laminated Panels, Printed Circuit Boards, Solar Modules  

## 5. Engineering Risks & FAQ
- **Caution**: 
- **Caution**: 
- **Caution**: 

### Q: What materials are used in pick-up head construction for durability?
**A**: Our pick-up heads are constructed from aluminum alloy for lightweight strength, stainless steel for corrosion resistance, engineering plastics like POM for wear resistance, and silicone/polyurethane suction cups for optimal grip and longevity in industrial environments.

### Q: How does the pick-up head ensure precise material transfer in lamination feeders?
**A**: The pick-up head integrates a precise lifting actuator with calibrated suction cups/grippers and vacuum control systems to consistently lift individual sheets from stacks without damage, ensuring accurate placement in downstream lamination processes.

### Q: What maintenance is required for pick-up heads in machinery manufacturing?
**A**: Regular inspection of suction cups for wear, cleaning of vacuum lines/valves to prevent clogging, and checking mounting brackets for alignment. Engineering plastic components may need periodic replacement based on usage cycles in high-volume operations.

## 6. Manufacturing Compliance
- ISO 1940-1:2003 (BALANCE QUALITY REQUIREMENTS FOR ROTORS)
- ANSI/ASME B46.1-2019 (SURFACE TEXTURE)
- DIN 7184-1:2018 (TOLERANCES FOR LINEAR DIMENSIONS)

---
### 🛠️ Engineering Resource Access
🔗 **[Full Specification: Pick-up Head](https://cnfx.com/industry/machinery-and-equipment-manufacturing/product/pick-up-head)**

### 🌐 Knowledge Graph Topology
> **Node Status**: Verified Engineering Spec
> **Connectivity**: Linked to **4** standalone system nodes
> **Global Context**: Part of a 5,814 node industrial cluster within the CNFX Graph

> **Reference ID**: PICK_UP_HEAD | **Authority**: CNFX-2026-ST-001 | **Fingerprint**: 887f2ce0
