INDUSTRY COMPONENT

Sensor Mounting Points

Precision mounting points for sensors in property measurement chambers.

Component Specifications

Definition
Sensor mounting points are precisely machined locations on the interior walls or fixtures of a property measurement chamber, designed to securely attach various sensors (e.g., temperature, humidity, pressure) for accurate and repeatable measurements. They ensure proper alignment, thermal isolation, and minimal interference with the chamber environment.
Working Principle
Mounting points provide a rigid, stable interface between the sensor and the chamber structure, often using threaded inserts or brackets to allow easy installation and removal. They are positioned to optimize sensor exposure to the measured property while minimizing dead zones and flow disturbances.
Materials
Typically stainless steel (304 or 316) for corrosion resistance and low outgassing; aluminum alloys for lightweight applications; or PTFE for chemical resistance.
Technical Parameters
ParameterTypical rangeNotes & selection driver
Depth12 mm
Spacing100 mm grid
Thread SizeM6 x 1.0
Load Capacity50 N
Surface FinishRa 0.8 μm

Ranges are indicative industry figures for RFQ preparation, not a supplier commitment. Confirm every value and standard with the legal manufacturer before ordering.

Standards
ISO 2768-1, DIN 509

Parent Products

This component is used in the following industrial products

Engineering Analysis

Risks & Mitigation
  • Thread stripping due to over-torquing
  • Misalignment causing measurement errors
  • Corrosion in harsh environments
FMEA Triads
Trigger: Over-torquing during installation
Failure: Thread stripping or cracking of mounting point
Mitigation: Use torque wrench with specified limit (e.g., 5 Nm)
Trigger: Thermal expansion mismatch
Failure: Sensor misalignment or binding
Mitigation: Select materials with similar CTE or use compliant washers

Industrial Ecosystem

Compatible With

Typical Suppliers & Equivalents

Compliance & Inspection

Tolerance
±0.1 mm for position, ±0.05 mm for perpendicularity
Test Method
Coordinate measuring machine (CMM) inspection per ISO 10360

Procurement Evaluation Criteria

A practical evidence checklist for RFQ preparation and supplier evaluation.

Technical documentation
Request current drawings, revision history, and a signed specification sheet.
Manufacturing capability
Verify equipment lists, process limits, capacity, and representative production evidence.
Inspection readiness
Confirm test methods, calibrated equipment, sampling plans, and traceable reports.
Supplier transparency
Check the legal entity, factory address, ownership, certifications, and direct contacts.

Compare the published product scope and source details, then include your specifications and quantity in an enquiry.

Manufacturers of Sensor Mounting Points

Manufacturer profiles associated with Sensor Mounting Points.

Sourcing Sensor Mounting Points from China?
Tell us your specification and target quantity — we will match it against manufacturer records and come back with the factories that fit.
Request manufacturers We manufacture this

Explore company information and manufacturing capabilities, then discuss the scope of your project with a relevant supplier.

Related Components

Chrome Plating
Hard chrome plating is an electroplating process that deposits a layer of chromium onto metal surfaces to enhance wear resistance, corrosion protection, and reduce friction for hydraulic cylinder piston rods.
Upper Tool (Punch)
Upper Tool (Punch) is the active forming component in metal plate bending machines that applies precise downward force to create bends in sheet metal.
Main Frame
The main frame is the primary structural component of a hydraulic press, providing rigidity and stability to withstand high compressive forces during metal forming operations.
Shaft Bearing
Precision component supporting rotating shafts in vibration motors to reduce friction and maintain alignment.

Frequently Asked Questions

What is the typical thread size for sensor mounting points?

Common thread sizes are M6 or 1/4-20 UNC, depending on the sensor standard.

Can mounting points be retrofitted to existing chambers?

Yes, but careful drilling and tapping are required to maintain chamber integrity and alignment.

Data Basis

Editorial classification, named public sources where available, and source-reviewed manufacturer records. See the editorial policy.

Preliminary Technical Classification
This page supports structured research, RFQ preparation, and supplier evaluation. It does not replace buyer-led supplier qualification, standards review, or technical approval.

Request Manufacturing Insight for Sensor Mounting Points

Thank you. Your request has been sent. We'll respond within 1–3 business days.
Sorry, we couldn't send your message. Please try again, or email us at [email protected].
Yoke Bracket
Get QuotesChat