Editorial Technical Reference

Self-tapping screw

Self-tapping screws · Insertion, tightening and stripping torque, thread geometry, pilot-hole ratios for plastics, driver speed, torque cut-off, plating and hydrogen embrittlement

A self-tapping screw is a hardened fastener with a tapered or pointed threaded shank that forms or cuts its own mating thread as it is driven into a pilot hole in plastic, sheet metal or wood, so no tapped hole or nut is needed. Ask three things first: which thread geometry suits the material it will be driven into, which pilot-hole size and engagement depth give a safe gap between insertion and stripping torque, and which material and finish suit the load and environment.

Thread-forming and thread-cutting self-tapping screws for plastics, sheet metal and similar materials. Self-drilling screws, drywall and chipboard screws, wood screws, machine screws and threaded inserts are outside this page.

CNFX editorial research · Sources checked October 12, 2026 · 4 sources

Self-Tapping Screw in a manufacturing environment
Representative product image. Confirm appearance and specifications with the manufacturer.

01

Set the torque window between insertion and stripping

Covestro's technical information on self-tapping screws for thermoplastics defines the insertion torque as the maximum torque reached before the screw head seats, and the stripping torque as the torque that strips the formed thread. It sets the tightening torque at least 1.2 times the insertion torque but not more than 0.5 times the stripping torque, says both should be measured experimentally, and states that the higher the ratio of stripping to insertion torque, the more reliable the joint. [1]

It lists causes of joints damaged in assembly: the kinetic energy of nut-runner masses that cannot be braked fast enough (especially at high speed with small screws), an unknown or misjudged stripping torque, and too small a screw-in depth; increasing screw-in depth raises stripping torque considerably with only a slight rise in insertion torque. [1]

Editorial calculation: if trials give an insertion torque of 0.5 N·m and a stripping torque of 2.0 N·m (assumed values), Covestro's rule allows tightening between 0.6 and 1.0 N·m; if the stripping torque were only 1.1 N·m, the window would shrink to 0.6–0.55 N·m and close. [1]

Give the supplier the material to be fastened (resin grade, glass content, or sheet thickness and grade), pilot-hole size, screw-in depth, thread form (thread-forming or thread-cutting), head and drive, required pull-out or clamp load, reuse cycles, screw material, hardness and finish, any baking requirement, driving equipment and quantities.

02

Size the screw, pilot hole and driving speed

For thermoplastics Covestro recommends screws with a sharp thread angle below 40°, a small core diameter below 0.65 × D, a high pitch above 0.35 × D and tight tolerances, and says countersunk heads are unsuitable because of their expanding effect. For screws without cutting notches of D = 2.9 to 5.1 mm its pilot-hole diameters are 0.86–0.89 × D for Bayblend PC+ABS, 0.90 × D for unreinforced Makrolon PC and Apec, and 0.92 × D for glass-fibre-reinforced Makrolon. [1]

Screws with a cutting notch cut the thread and suit single or few assemblies; reducing the hole diameter to meet repeated-assembly requirements raises boss expansion and the risk of long-term stress cracking. Screw circumferential speeds of 3–6 m/min have proved successful, about 250–500 rpm for a 4 mm screw; too much frictional heat lowers the stripping torque. Screws should be free from cutting oil or rust-protection residues that can cause stress cracking. [1]

NASA's Fastener Design Manual notes that plating processes can generate hydrogen, so plated steel fasteners must be baked after plating to prevent hydrogen embrittlement, and that dissimilar metals in contact can cause galvanic corrosion. [2]

A patented thread-forming screw for harder plastics from Illinois Tool Works takes a different route: an asymmetric thread with a flank angle of about 30°, split into a leading angle of 20° ± 2° and a trailing angle of 10° ± 1°, and a smaller pitch for more threads per inch. For an M5.0 screw the patent gives a pitch of 1.15–1.35 mm (1.25 mm preferred, ±0.10 mm) against conventional pitches of about 2.25 mm, a thread outside diameter of 5.0–5.25 mm and a core diameter of 3.80–4.00 mm, an outside-to-core ratio of about 1.30:1; M4.0 examples have a 0.90–1.10 mm pitch and a 3.0–3.20 mm core. [4]

Editorial calculation: the patent's M5.0 example has a core of about 3.9 / 5.1 ≈ 0.76 × D and a pitch of 1.25 / 5.0 = 0.25 × D, outside Covestro's general guidance of a core below 0.65 × D and a pitch above 0.35 × D; the patent trades the larger core and finer pitch for pull-out resistance, so ask which design rule a quoted screw follows. [1] [4]

Editorial calculation: for a 3.5 mm screw in unreinforced Makrolon, the pilot hole is 0.90 × 3.5 ≈ 3.15 mm; at 250 rpm a 4 mm screw's thread moves π × 4 mm × 250 ≈ 3.1 m/min, matching Covestro's lower speed limit. [1]

03

Pick a pilot hole from a screw maker's material factors

TR Fastenings' installation guide for its Plas-Tech 30 screw for plastics (a 30° flank angle and 8° pitch angle, with a profiled thread root) sizes the hole by multiplying a material factor by the nominal thread diameter d: for example 0.80d for ABS, so a 3.0 mm screw in ABS takes a 2.4 mm guideline hole. It recommends a counterbore 0.2 mm larger than the published head diameter to protect the top of the boss and relieve extruded material, and says the screws can go into moulded holes with a 1° inclusive taper or into drilled holes. [3]

The factors show glass-filled grades taking a larger hole than the same unfilled resin (0.80d for PA6 GF30 against 0.75d for PA6). [3] Compare these with the pilot-hole table and torque window from Covestro and the fastener design data from NASA above, and confirm by trials on your boss. [1] [2]

Editorial calculation: hole diameters in the table are factor × 3.0 mm; for a 4.0 mm screw in PC the 0.85d factor gives 3.4 mm.

Material (TR Plas-Tech 30)Hole factor AHole for d = 3.0 mm (editorial)
ABS; ABS/PC0.80d2.40 mm
PA6; PA6.6; PBT; PP; POM0.75d2.25 mm
PA6 GF30; PBT GF300.80d2.40 mm
PA6.6 GF300.82d2.46 mm
PC; PC GF30; PMMA; PVC0.85d2.55 mm
LDPE0.70d2.10 mm

Give the screw supplier your resin grade, filler content and boss drawing, and ask for its hole factor and recommended counterbore for that grade.

04

Compare what suppliers offer

Suppliers linked to this page list self-tapping screws; each card links to the page reviewed.

Listings include pan, hex and other head self-tapping screws among machine, drywall, chipboard and self-drilling screws.

05

Trace what defines the screw

This is a functional reference built from the sources cited; it is not one maker's design.

FeatureRoleFix in the order
Thread formForms or cuts mating thread. [1]Angle, pitch, core.
Point and notchStarts the thread. [1]With or without cutting notch.
HeadBears on the part. [1]Style; avoid countersunk in plastics.
Material and hardnessForms thread without wear.Steel grade, case depth.
FinishCorrosion; embrittlement risk. [2]Plating and baking.
CleanlinessAvoids stress cracking. [1]Residue-free supply.

06

Fill the specification fields with values for your joint

A self-tapping screw quotation needs values for your joint. The table explains each field, gives published values where a reviewed source states them, and says what to obtain from the supplier.

FieldWhat it means and published valuesAsk the supplier for
ThreadFlank angle below 40°, core below 0.65 × D for plastics. [1]Thread form and size.
Pilot hole0.86–0.92 × D in one maker's resins. [1]Recommended hole.
Tightening torque1.2 × insertion to 0.5 × stripping torque. [1]Measured torques.
Driving speed3–6 m/min; 250–500 rpm at 4 mm. [1]Speed and cut-off.
MaterialSteel or stainless.Grade and hardness.
FinishBake after plating. [2]Finish and baking.
Pilot hole factorExamples: 0.75d (PA6, PP, POM) to 0.85d (PC, PVC); 2.4 mm for 3.0 mm in ABS (TR Plas-Tech 30). [3]Hole factor for your resin grade.
Pitch and core (patented example)M5.0: pitch 1.15–1.35 mm, core 3.80–4.00 mm, flank about 30° (ITW patent). [4]Pitch, core and flank angle on the drawing.

07

Send the material, hole and torque data together

Paste it into your enquiry below or into an email to a maker, then replace every bracket.

Material: [resin or sheet; grade; thickness]
Hole: [pilot diameter; depth]
Screw: [size; thread form; head; drive]
Torque: [insertion; tightening; stripping]
Finish: [type; baking; cleanliness]
Supply: [reuse cycles; quantity]

See manufacturer records Send an enquiry through CNFX

Compare self-tapping screw suppliers

These companies list self-tapping screws.

Haiyan Bolt Co., Ltd.
Manufacturing site to be confirmed for the order

Lists self-tapping screws on a dedicated product page.

Product scope checked 2026-10-11

Current product source ↗

Self-tapping screws listed · profile compiled by CNFX from public sources
Tianjin Sinsun Imp & Exp Co., Ltd.
Manufacturing site to be confirmed for the order

Lists pan head and other self-tapping screws.

Product scope checked 2026-10-11

Current product source ↗

Self-tapping screws listed · profile compiled by CNFX from public sources
Tianjin Xinruifeng Technology Co., Ltd.
Manufacturing site to be confirmed for the order

Lists self-tapping screws among drywall, chipboard and self-drilling screws.

Product scope checked 2026-10-11

Current product source ↗

Self-tapping screws listed · profile compiled by CNFX from public sources
Tianjin Huazhen Fastener Co., Ltd.
Manufacturing site to be confirmed for the order

Lists hexagonal and other self-tapping screws among drywall and self-drilling screws.

Product scope checked 2026-10-11

Current product source ↗

Self-tapping screws listed · profile compiled by CNFX from public sources
Wenzhou City Jinghong Fasteners Co., Ltd.
Manufacturing site to be confirmed for the order

Lists self-tapping screws among screws and fasteners.

Product scope checked 2026-10-11

Current product source ↗

Self-tapping screws listed · profile compiled by CNFX from public sources
Ningbo Fastenwell
Manufacturing site to be confirmed for the order

Lists self-tapping screws among screws and fasteners.

Product scope checked 2026-10-11

Current product source ↗

Self-tapping screws listed · profile compiled by CNFX from public sources
Shuifu Hanyang Machinery Technology Co., Ltd.
Manufacturing site to be confirmed for the order

Lists self-tapping screws among screws and fasteners.

Product scope checked 2026-10-11

Current product source ↗

Self-tapping screws listed · profile compiled by CNFX from public sources
Gangtong Zheli Fasteners
Manufacturing site to be confirmed for the order

Lists self-tapping screws among screws and fasteners.

Product scope checked 2026-10-11

Current product source ↗

Self-tapping screws listed · profile compiled by CNFX from public sources
Taishin Machinery Co., Ltd.
Manufacturing site to be confirmed for the order

Lists self-tapping screws among screws and fasteners.

Product scope checked 2026-10-11

Current product source ↗

Self-tapping screws listed · profile compiled by CNFX from public sources
HEBEI HENGCHENG FASTENER CO., LTD.
Handan, Hebei, CN
Listed on the company's own website · profile compiled by CNFX from public sources
Listed there as: “Self-tapping Screw”
View source page ↗ hfastfix.com · recorded 2026-10-11
XiYu Precision Technology (Dongguan) Co., Ltd.
Guangdong, CN
Also makes: Machine Screw
Listed on the company's own website · profile compiled by CNFX from public sources
Listed there as: “Self-Drilling & Self-Tapping Screws”
View source page ↗ xiyuprecision.com · recorded 2026-09-14
View All Factories

Explore company information and manufacturing capabilities, then discuss the scope of your project with a relevant supplier.

Buyer questions

How tight should a self-tapping screw be in plastic?

Covestro sets tightening torque at least 1.2 times the insertion torque and no more than half the stripping torque. [1]

What pilot hole should be used in plastic?

Covestro recommends 0.86–0.92 times the screw diameter depending on resin, for D = 2.9 to 5.1 mm. [1]

Can countersunk self-tapping screws be used in plastics?

Covestro says countersunk heads are unsuitable for thermoplastics because of their expanding effect. [1]

What pilot hole does a self-tapping screw for plastic need?

TR Fastenings multiplies a material factor by the screw diameter: 0.80d for ABS (2.4 mm for a 3.0 mm screw), 0.75d for PA6 or PP, 0.85d for PC. [3]

Does a finer pitch help a thread-forming screw hold in plastic?

Illinois Tool Works' patent US 6,702,537 B2 uses a 1.15–1.35 mm pitch on an M5.0 screw, against about 2.25 mm for conventional screws, to raise pull-out resistance, with a flank angle of about 30° to reduce cracking in harder plastics. [4]

Sources and what still needs a direct check

Sources checked 2026-10-12. Covestro is a plastics maker giving guidance for its own resins; TR Fastenings publishes hole factors for its own screw; Illinois Tool Works' patent describes one thread-forming design; NASA's manual is general fastener guidance. Values for your joint must come from trials and the supplier.

  1. Covestro — Self-tapping screws for thermoplastics, technical information (PCS-1114, edition 2016-04, PDF) ↗ Material maker guidance Return to text ↑
  2. NASA — Fastener Design Manual, Reference Publication 1228 (1990, PDF) ↗ Government technical manual Return to text ↑
  3. TR Fastenings — Plas-Tech 30 installation guide and hole sizes ↗ Maker installation guide Return to text ↑
  4. Illinois Tool Works — US 6,702,537 B2, High profile thread forming screw (Google Patents) ↗ Patent Return to text ↑

Still to check yourself

  • Measure insertion and stripping torque.
  • Size pilot hole for the material.
  • Set speed and torque cut-off.
  • Confirm finish and baking.
  • Verify the legal supplier and factory.
Buyer enquiry

Request manufacturing insight for Self-Tapping Screw

Ask for use case, specification boundaries, supplier type, and RFQ preparation information for this product.

Where it goes
Straight to the CNFX editorial desk, and to the manufacturer if this product is linked to a claimed profile. Nothing is broadcast to a supplier list.
Your details stay here
We do not sell or rent enquiry data, and we do not add you to a mailing list. Used only to answer this request.
No commission, no middleman
CNFX is a directory. We take no cut of any order and never negotiate on a supplier's behalf.
What to include
Share your product specifications, quantity, destination and target delivery date.

Your business information is used only to process this request.

Thank you! Your message has been sent. We'll respond within 1–3 business days.
Sorry, we couldn't send your message. Please try again, or email us at [email protected].

Need to Manufacture Self-Tapping Screw?

Compare manufacturer profiles with relevant product and process capability.

Previous Product
Welding Positioner
Last Product
Get QuotesChat