Manual hand pallet trucks (pallet jacks) · Rated capacity at load centre, lowered and raised fork height, low-profile versions for low pallets, manual-handling training and capacity plates
A hand pallet truck, or pallet jack, is a manually pushed truck whose forks slide under a pallet and are raised a few centimetres by pumping the handle, so the pallet can be moved across a floor. Ask three things first: the heaviest load and how it sits on the forks, since capacity is rated at a load centre; the lowest pallet opening and fork length the pallets need; and the floors, ramps and distances it will work on, since it is moved by human effort.
Manual hand pallet trucks (pallet jacks) — standard, low-profile, long-fork and heavy-capacity versions. Electric pallet trucks, pallet stackers, order pickers, forklifts and lifting slings are outside this page except where compared.
01
Toyota describes a hand pallet jack as forks that slide under pallets, a hydraulic pump worked by moving the handle up and down, and wheels, able to lift pallets "several inches off the ground" and move loads by human power. Its hand pallet jacks are rated 5,500 lb (2,500 kg), which it calls the industry standard for heavy-duty models, assuming evenly distributed loads at a standard 24 in load centre; exceeding it can damage the hydraulics, bend the forks and create hazards, so the capacity plate on the specific model must be checked. [2] [1]
Toyota's standard HPT28U has a lowered fork height of about 3.0 in and a raised height of about 7.75 in; low-profile versions with shortened load wheels and revised fork geometry reach about 2.0 in, in some cases 1.75 in, for low-clearance pallets, with capacity lower than the standard 5,500 lb model. [1]
Editorial calculation: 5,500 lb is about 2,495 kg and a 24 in load centre about 610 mm; 3.0 in lowered is about 76 mm, 7.75 in raised about 197 mm, giving about 121 mm of lift, and a 2.0 in low-profile fork is about 51 mm. [1]
Give the supplier the heaviest load and its centre of gravity, pallet type and lowest opening height, fork length and overall width, raised height needed, wheel and roller material for your floors, handle and brake options, ramps or gradients, operating temperature (for example cold stores), corrosion protection, weighing or other options, and quantity.
02
Toyota says OSHA does not require certification for hand pallet jack operators, because hand pallet jacks are treated as hand tools, unlike electric pallet jacks, which are powered industrial trucks; it advises employers still to train operators on safe operation, load limits and site hazards. It also classes hand pallet jacks as manual handling equipment, since operators pump the hydraulics and push or pull the load, and advises following manual-handling guidance on posture and avoiding excessive loads. [2]
Editorial note: because the truck is moved by hand, ask the supplier for the push or pull force needed to start and keep a rated load moving on your floor, and for wheel options suited to rough floors, ramps or dock plates.
03
Suppliers linked to this page list hand pallet trucks; each card links to the page reviewed.
Listings include standard and heavy-duty hand pallet trucks up to 5 t, adjustable-fork pallet trucks, manual stackers and electric pallet trucks; ask each for the capacity plate, lowered and raised fork heights, fork dimensions, wheel material and the standard the truck is built to.
04
Jungheinrich's product details for its AM 22 hand pallet truck with 2,400 mm forks, offered for long goods or for carrying multiple pallets at once and also available with 1,600 and 1,900 mm forks, give a capacity of 500 kg at a 1,200 mm load centre distance. [4]
This version has tandem polyurethane fork rollers 82 mm in diameter, a 170 mm solid-rubber steering wheel, entry rollers, and lowering speeds of 0.09 m/s with load and 0.02 m/s without. [4]
Editorial calculation: 500 kg is about 22% of the 2,300 kg rating of Crown's standard-fork PTH 50 (500 ÷ 2,300 ≈ 0.22). [4] [3] For long or multiple loads, ask each supplier for the rated capacity at your fork length and load centre, not the headline rating of the model family.
| Item | Jungheinrich AM 22, 2,400 mm forks | Compare with |
|---|---|---|
| Capacity and load centre | 500 kg at 1,200 mm [4] | 2,300 kg, Crown PTH 50 [3] |
| Lift range and lift | 83–205 mm; 122 mm [4] | 127 mm lift, Crown PTH 50 [3] |
| Pump strokes | 7 to lift a pallet, 12 to maximum height, 10 mm per stroke [4] | Ask each supplier |
| Net weight | 90 kg [4] | 55–70 kg, Crown PTH 50 [3] |
| Fork width and width across forks | 150 mm and 520 mm [4] | 160 mm and 520 mm, Crown PTH 20 [3] |
| Turning radius | 2,524 mm [4] | Check against aisle width |
05
Crown's PTH 50 Series brochure gives the dimensions that a quotation needs. Every model in the table is rated 2,300 kg, with forks 160 mm wide, a lift height of 127 mm, 30 mm ground clearance, polyurethane tyres, 180 × 50 mm steer wheels and 74 × 98 mm load wheels. Fork lengths of 795, 990 and 1,150 mm give overall truck lengths of 1,155, 1,350 and 1,510 mm, and the load wheels sit 648, 843 and 1,003 mm from the fork heel when lowered. Outside fork spreads are 450, 520 or 685 mm, and truck weights run from 55 kg to 70 kg. Crown also states a 75 mm fork clearance. [3]
Crown says the pump valve is tested to over one million cycles and uses hard chrome pistons against contamination and corrosion, and that the 180 mm articulating wheels keep floor contact over uneven surfaces, across docks and in and out of trailers. Its 3-year supplemental warranty covers the pump assembly, frame, handle, lift linkage and pushrod weldments, and excludes the PTH 50S and PTH 50PS scissor-lift models. Ask each supplier for its pump cycle test and warranty scope in the same terms. [3]
Editorial calculation: Crown's 2,300 kg rating is 200 kg below Toyota's 2,500 kg (2,500 − 2,300 = 200), so the same nominal truck type can carry different rated loads from different makers. Compare the capacity plate and load centre of each quoted model against your heaviest pallet rather than assuming one rating applies across suppliers. [3] [2]
06
This is a functional reference built from the sources cited; it is not one maker's specification.
| Element | Role | Fix in the order |
|---|---|---|
| Forks | Slide under the pallet. [2] | Length, width, lowered height. |
| Hydraulic pump | Raises forks by pumping the handle. [2] | Pump, release valve. |
| Load wheels | Carry the load under the forks. [1] | Size, material. |
| Steer wheels and handle | Push, pull and steer. | Material, brake. |
| Capacity plate | States rated load. [2] | Capacity and load centre. |
07
A hand pallet truck quotation needs values for your pallets. The table explains each field, gives published values where a reviewed source states them, and says what to obtain from the supplier.
| Field | What it means and published values | Ask the supplier for |
|---|---|---|
| Load capacity (kg) | 2,500 kg at 24 in load centre (Toyota). [2] | Capacity plate. |
| Fork length (mm) | Not stated in reviewed sources. | Length. |
| Fork width (mm) | Not stated in reviewed sources. | Overall width. |
| Lift height (mm) | Raised ~7.75 in (197 mm). [1] | Raised height. |
| Lowered fork height (mm) | ~3.0 in; low-profile ~2.0 in. [1] | Lowered height. |
| Overall length (mm) | Not stated in reviewed sources. | Length. |
| Overall width (mm) | Not stated in reviewed sources. | Width. |
| Net weight (kg) | Not stated in reviewed sources. | Weight. |
| Hydraulic oil type | Not stated in reviewed sources. | Oil, cold-store option. |
| Operating temperature (°C) | Not stated in reviewed sources. | Range. |
| Wheel material | Not stated in reviewed sources. | Load and steer wheels. |
08
Paste it into your enquiry below or into an email to a maker, then replace every bracket.
Load: [heaviest; centre of gravity] Pallets: [type; opening height; size] Forks: [length; overall width; lowered and raised height] Wheels: [material for floor] Site: [ramps; distances; cold store] Options: [brake; scale; corrosion protection] Quantity: [units]
These companies list hand pallet trucks.
Lists hydraulic pallet trucks with electric pallet trucks.
Product scope checked 2026-10-11
Lists hand pallet trucks.
Product scope checked 2026-10-11
Lists hand pallet trucks and walkie electric pallet trucks.
Product scope checked 2026-10-11
Lists hand pallet trucks with lifting slings and hoists.
Product scope checked 2026-10-11
Lists hand and electric pallet trucks.
Product scope checked 2026-10-11
Lists hand pallet trucks and manual stackers.
Product scope checked 2026-10-11
Lists hand pallet trucks with electric pallet trucks.
Product scope checked 2026-10-11
Lists hand and electric pallet trucks.
Product scope checked 2026-10-11
Lists hand and electric pallet trucks.
Product scope checked 2026-10-11
Explore company information and manufacturing capabilities, then discuss the scope of your project with a relevant supplier.
Toyota's standard hand pallet jacks are rated 5,500 lb (2,500 kg) with an evenly spread load at a 24 in load centre. [2]
About 3.0 in on Toyota's standard model and about 2.0 in (some 1.75 in) on low-profile versions. [1]
Toyota says OSHA does not require it for hand pallet jacks, unlike powered pallet trucks, but training is still advised. [2]
Crown's PTH 50 Series brochure lists 795, 990 and 1,150 mm forks with outside fork spreads of 450, 520 or 685 mm and each fork 160 mm wide, all rated 2,300 kg. [3]
Sources checked 2026-10-11. Both sources are from Toyota Material Handling describing its own hand pallet jacks; its OSHA remarks are its interpretation, so check local rules.
Ask for use case, specification boundaries, supplier type, and RFQ preparation information for this product.
Compare manufacturer profiles with relevant product and process capability.